Performance characteristic:

1. The soldering tin rifle adopts the light and handy organization to design; it is more relaxed to work.

2.      Generate heat core while being high-quality, have longer working lives.

3.      It is simple to operate. It is apt to finish welding the homework.

4.      Amount uses the diameter as the tin thread of 0.8.3mm.

5.      Use voltage of 110 VAC or 220 VAC

Operation method

1.      When the hand welding torch is used for the first time, must preheat for several minutes, phenomena are to belong to the normal one to smolder, will disappear in several seconds.

2.Insert the specified tin mouth from entering of tin line, then pull the trigger according to the arrow point direction, can work normally until the tin silk sends and leads the tin to manage the mouth to stop.

3. While needing to withdraw from or change the tin silk while stopping using, so long as extremely stiff the direction will be promoted upwards, will take out the tin silk at the same time.

4. At is it generate heat core to changing, is it pull down to stamp protecting first, is it generate heat core line to disassemble, pull down flatiron chew, can is it generate heat the core to change again.

Precautions

1. While working, the temperature that the flatiron is chewed and the flatiron is in charge of is up to more than 400 degrees, forbid the human body to touch so as not to burn.

2. When the hand welding torch stops using, please put it on its support.

3. Work after finishing, close power, etc. is it put to keep after the complete cooling.

1. Pedal switch, give the tin automatically.

2. Ration the tin function happens.

3. Temperature can be adjusted by oneself.

4. It is simple and easy to operate, improve more than 50% of the working efficiency.

5. Needn't use the soldering tin lotion to weld the homework while doing.

6.There is digital display function of temperature, and actual temperature keeps unanimity.

This machine adopts the high-quality synchronous electrical machinery to urge, the tooth shape metal leads the tin wheel, it is steady to guarantee to send the tin, the speed is invariable, and the solder joint is unanimous in size.

Flatiron head temperature adopts the warm accusing of device of knob to regulate.

This machine suitable tin silk thread foot-path: 0.8mm\1.0mm\1.2mm. Please choose according to the size of solder joint.

This soldering tin machine is especially suitable for all kinds of electronic connectors, light bunch of LED, video audio frequency line plug, an earphone thread, computer data line, the welding and connecting the middle small-scale circuit board and online bunch of small-scale electronic devices and components,etc.

一． Technical parameter

Specified voltage: 22040V frequency: 50/60Hz rated power: 500W 700W (two style)

二． Main use

Plastic welding torch weld various kinds of plastic equipment and indispensable tool at maintaining the plastic equipment of form with plastic welding rod plastic board, this product is suitable for the section and accumulated and greater than 6m ©O plastic welding rod to weld function. Can mix and chew with the spear while using.

三． Use the item

    1.There are temperature adjustment switches on the handle, twist to right " pa " In order to close the power after, twist to the left " pa " Green indicator lamp is on after, open the cold wind, when the red indicator lamp of and then twisting to the left etc. Dr.eye: is on, begin to send the hot wind, until twisting it while moving, temperature reaches highest.

     2.Use it in the course, regulate temperature in good time according to the need, pay attention to the distance between the spray nozzle and solder joint, reach the demand that the ideal welds.

    3.While using for the first time, may smolder or take the Mars phenomenon, this phenomenon is belonging to the normal one. Disappear automatically several seconds later.

     4.Should keep the tail of the welding torch entering the wind smoothly while using, otherwise is it generate heat core to be overheated to burn out to result in.

    5.It weld after finishing,switch it twist it is to cold wind shelf (already red light put out after) ,Give the cold wind for a moment, make steel tube and generate heat core is it come down to cool, then shut-down. Can protect heating wire to be remaining energy too high to be it generate heat core burn out the lead wire after the life-span to influence effectively in this way. By finishing putting down to this product gently keeping, so as not to damage some refractory materials of welding torch, cause the heating wire broken and fall.

   6.Such as generate heat core burn out, can is it shoot shell join screw is it generate heat the core to take out, needn't open the handle to fasten, change the generating heat of the same type core of our factory.

   7.While using, there must be ground wire to join, guarantee the security.

四． Precautions

    1.Can't be in the moist environment work of air, so as not to get an electric shock.

    2.Can't touch steel tube generate heat some, so as not to burn while using.

    3. Forbid using and moulding the welding torch flammable, explosive article nearby, so as to avoid the contingency.

    4. After finishing using, should keep and put the steel pipe carrier properly on the support, after complete cooling.

五． Related enclosure

    Generate heat the core   One is extended and chewed  One